Infiniti Vehicle Models I30 1996-1999 Torque Specifications
Infiniti Vehicle Models I30 1996-1999

Infiniti Vehicle Models I30 1996-1999 Torque Specifications

Complete Infiniti Vehicle Models I30 1996-1999 torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.

Updated

Important Information

Safety guidelines and reference information for proper torque application

Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083

Common Torque Patterns

Star Pattern

Used for wheels and other circular bolt patterns

Star Pattern torque pattern diagram showing proper bolt tightening sequence
Cross Pattern

Used for gaskets and cover plates

Cross Pattern torque pattern diagram showing proper bolt tightening sequence
Sequential Pattern

Used for head bolts and other critical components

Sequential Pattern torque pattern diagram showing proper bolt tightening sequence

Common Mistakes to Avoid

Over-tightening

Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.

Prevention:

Always use a calibrated torque wrench and follow specifications exactly.

Incorrect Torque Sequence

Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.

Prevention:

Follow the manufacturer's specified torque sequence pattern.

Dirty Threads

Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.

Prevention:

Clean and inspect all threads before assembly. Use new thread locker if specified.

Reusing TTY Bolts

Torque-to-yield bolts are designed to stretch and must not be reused.

Prevention:

Always replace TTY bolts with new ones. They are single-use only.

Dry vs. Lubricated

Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.

Prevention:

Check if specs are for dry or lubricated threads. Use specified lubricant when required.

Recommended Tools

Torque Wrench (1/4" Drive)

Range: 2-25 ft-lbs
Small fasteners, delicate components

Torque Wrench (3/8" Drive)

Range: 10-100 ft-lbs
Most common automotive fasteners

Torque Wrench (1/2" Drive)

Range: 30-250 ft-lbs
Large fasteners, wheels

Angle Gauge

Torque-to-yield (TTY) bolts

Torque Wrench Care

  • Calibrate annually or after 5,000 clicks
  • Store at lowest setting
  • Keep clean and lubricated

Search Specifications

Search by component name, bolt size, or description

Torque Calculator

Convert between different torque units

3.0l Engine

Torque specifications for 3.0L Engine

Cylinder Head

1

Cylinder Head Bolts

M10 x 1.25
Torque Specification
1. 23 ft-lbs (31 N·m) 2. 90°
Important Notes
Follow the manufacturer's specified torque sequence to prevent warping.
2

Valve Cover Bolts

M6 x 1.0
Torque Specification
4 ft-lbs (5.4 N·m)
Important Notes
Use a crisscross pattern to ensure even sealing.

Crankshaft And Bearings

1

Main Bearing Bolts

M10 x 1.25
Torque Specification
50 ft-lbs (68 N·m)
Important Notes
Follow the specified torque sequence to ensure proper crankshaft alignment.
2

Connecting Rod Nuts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the connecting rod caps are properly aligned before tightening.

Timing System

1

Camshaft Sprocket Bolt

M12 x 1.5
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Ensure the timing marks are aligned before tightening.
2

Timing Belt Tensioner Bolt

M8 x 1.25
Torque Specification
19 ft-lbs (26 N·m)
Important Notes
Ensure proper belt tension before tightening.

Intake And Exhaust

1

Intake Manifold Bolts

M8 x 1.25
Torque Specification
14 ft-lbs (19 N·m)
Important Notes
Follow the specified torque sequence to ensure a proper seal.
2

Exhaust Manifold Bolts

M8 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Use a crisscross pattern to ensure even sealing.

Oil System

1

Oil Pan Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Use a crisscross pattern to ensure even sealing.
2

Oil Drain Plug

M14 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Replace the crush washer to prevent leaks.

3.0l V6 Engine

Torque specifications for 3.0L-V6 Engine

Cylinder Head

1

Cylinder Head Bolts

M10 x 1.25
Torque Specification
1. 23 ft-lbs (31 N·m) 2. 90°
Important Notes
Follow the manufacturer's specified torque sequence to prevent warping.
2

Valve Cover Bolts

M6 x 1.0
Torque Specification
4 ft-lbs (5.4 N·m)
Important Notes
Use a crisscross pattern to ensure even sealing.

Crankshaft And Bearings

1

Main Bearing Bolts

M10 x 1.25
Torque Specification
50 ft-lbs (68 N·m)
Important Notes
Follow the specified torque sequence to ensure proper crankshaft alignment.
2

Connecting Rod Nuts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the connecting rod caps are properly aligned before tightening.

Timing System

1

Camshaft Sprocket Bolt

M12 x 1.5
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Ensure the timing marks are aligned before tightening.
2

Timing Belt Tensioner Bolt

M8 x 1.25
Torque Specification
19 ft-lbs (26 N·m)
Important Notes
Ensure proper belt tension before tightening.

Intake And Exhaust

1

Intake Manifold Bolts

M8 x 1.25
Torque Specification
14 ft-lbs (19 N·m)
Important Notes
Follow the specified torque sequence to ensure a proper seal.
2

Exhaust Manifold Bolts

M8 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Use a crisscross pattern to ensure even sealing.

Oil System

1

Oil Pan Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Use a crisscross pattern to ensure even sealing.
2

Oil Drain Plug

M14 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Replace the crush washer to prevent leaks.

4r01 Transmission

Torque specifications for 4r01 Transmission

Transmission Mounting

1

Transmission Mounting Bolts

M12 x 1.5
Torque Specification
32.5 ft-lbs (44 N·m)
Important Notes
Estimated average value from the given range.

Transmission Case

1

4R01 Transmission Case Bolts (Upper and Lower)

M14 x 1.5
Torque Specification
46.5 ft-lbs (63 N·m)
Important Notes
Estimated average value from the given range.

Transmission Bellhousing

1

4R01 Transmission Bellhousing Bolts

M12 x 1.5
Torque Specification
32.5 ft-lbs (44 N·m)
Important Notes
Estimated average value from the given range.

Transmission Oil Pan

1

Transmission Oil Pan Bolts

M10 x 1.5
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Estimated average value from the given range.
2

4R01 Transmission Pan Gasket Bolts

M8 x 1.25
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Estimated average value from the given range.

Transmission Fluid System

1

Transmission Drain and Fill Plugs

M16 x 1.5
Torque Specification
25.5 ft-lbs (34.5 N·m)
Important Notes
Estimated average value from the given range.
2

Transmission Fluid Drain/Fill Plug

M16 x 1.5
Torque Specification
25.5 ft-lbs (34.5 N·m)
Important Notes
Estimated average value from the given range.
3

4R01 Transmission Filter Bolts

M8 x 1.25
Torque Specification
15.5 ft-lbs (21 N·m)
Important Notes
Estimated average value from the given range.

Body

Torque specifications for Body

Suspension

1

Strut/Shock Absorber Mounting Bolts

M14 x 1.5
Torque Specification
25.5 ft-lbs (34.5 N·m)
Important Notes
Estimated value based on similar components and bolt sizes.
2

Control Arm Bolts

M16 x 1.5
Torque Specification
59.5 ft-lbs (80.5 N·m)
3

Ball Joint Nut

M12 x 1.5
Torque Specification
39.5 ft-lbs (53.5 N·m)

Steering

1

Tie Rod End Nut

M12 x 1.5
Torque Specification
25.5 ft-lbs (34.5 N·m)
2

Steering Gear/Rack Bolts

M14 x 1.5
Torque Specification
65 ft-lbs (88 N·m)

Body

1

Body Mount Bolts

M16 x 1.5
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Estimated value based on general industry standards.
2

Door Hinge Bolts

M10 x 1.5
Torque Specification
17.5 ft-lbs (23.5 N·m)
Important Notes
Estimated value based on general industry standards.
3

Hood Hinge Bolts

M10 x 1.5
Torque Specification
17.5 ft-lbs (23.5 N·m)
Important Notes
Estimated value based on general industry standards.
4

Trunk Lid Hinge Bolts

M10 x 1.5
Torque Specification
17.5 ft-lbs (23.5 N·m)
Important Notes
Estimated value based on general industry standards.
5

Bumper Mounting Bolts

M12 x 1.5
Torque Specification
22.5 ft-lbs (30.5 N·m)
Important Notes
Estimated value based on general industry standards.

Brakes

Torque specifications for Brakes

Brake Caliper

1

Brake Caliper Bolts

M10 x 1.25
Torque Specification
22.5 ft-lbs (30.5 N·m)
Important Notes
Torque value is an average of the provided range (20-25 ft-lbs).
2

Brake Caliper Mounting Bracket Bolts

M12 x 1.5
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Torque value is an average of the provided range (58-72 ft-lbs).

Brake Rotor Drum

1

Brake Disc/Drum Retaining Bolts

M8 x 1.25
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Torque value is an average of the provided range (5-7 ft-lbs).

Brake Hydraulics

1

Brake Hose Banjo Bolt

M10 x 1.0
Torque Specification
19 ft-lbs (26 N·m)
Important Notes
Torque value is an average of the provided range (16-22 ft-lbs).
2

Brake Master Cylinder Mounting Bolts

M8 x 1.25
Torque Specification
13.5 ft-lbs (18 N·m)
Important Notes
Torque value is an average of the provided range (12-15 ft-lbs).

Brake Booster Pedal

1

Brake Booster Mounting Bolts

M10 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Torque value is an average of the provided range (18-22 ft-lbs).
2

Brake Pedal Assembly Bolts

M10 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Torque value is an average of the provided range (18-22 ft-lbs).

Wheel Assembly

1

Wheel Lug Nuts

M12 x 1.5
Torque Specification
80 ft-lbs (108 N·m)
Important Notes
Torque value is an average of the provided range (72-87 ft-lbs).

Drivetrain

Torque specifications for Drivetrain

Engine

1

Flywheel Bolts

M12 x 1.5
Torque Specification
54 ft-lbs (73 N·m)
Important Notes
Proper torque is essential to prevent damage to the flywheel, crankshaft, and transmission.
2

Main Bearing Bolts

M14 x 1.5
Torque Specification
47 ft-lbs (64 N·m)
Important Notes
Proper torque ensures the bearings are securely fastened and prevents engine damage.
3

Connecting Rod Nuts

M10 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Proper torque is crucial to prevent engine damage and ensure proper engine operation.

Transmission

1

Transmission Pan Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Proper torque is essential to prevent leaks and damage to the transmission. (Estimated value)
2

Transmission Mounting Bolts

M12 x 1.5
Torque Specification
29 ft-lbs (39 N·m)
Important Notes
Proper torque ensures the transmission is properly aligned and supported.

Driveshaft and Axles

1

Drive Axle/Half Shaft Bolts

M14 x 1.5
Torque Specification
29 ft-lbs (39 N·m)
Important Notes
Proper torque is essential to prevent damage to the axles and transmission.
2

CV Joint/Axle Nut

M18 x 1.5
Torque Specification
174 ft-lbs (236 N·m)
Important Notes
Proper torque is crucial to prevent damage to the CV joint and axle.

Differential and Transfer Case

1

Differential Cover Bolts

M10 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Proper torque is essential to prevent leaks and damage to the differential. (Estimated value)
2

Differential Drain/Fill Plug

M12 x 1.5
Torque Specification
36 ft-lbs (49 N·m)
Important Notes
Proper torque is essential to prevent leaks and damage to the differential.

Electrical

Torque specifications for Electrical

Ignition System

1

Ignition Coil Bolt

M8 x 1.25
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Estimated value based on similar components. Proper torque is essential to prevent damage to the coil.
2

Spark Plug Wire Boot Clamp Bolt

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Estimated value based on general industry standards.
3

Ignition Module Mounting Bolt

M10 x 1.5
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Estimated value based on general industry standards.

Starting System

1

Starter Motor Mounting Bolts

M12 x 1.75
Torque Specification
32 ft-lbs (43 N·m)
Important Notes
Proper torque is essential to prevent damage to the starter motor or engine block.

Charging System

1

Alternator Mounting Bolts

M12 x 1.75
Torque Specification
32 ft-lbs (43 N·m)
Important Notes
Proper torque is essential to prevent damage to the alternator or engine block.
2

Alternator Belt Tensioner Bolt

M10 x 1.5
Torque Specification
19 ft-lbs (26 N·m)
Important Notes
Estimated value based on general industry standards.

Electrical System

1

Battery Terminal Nuts

M8 x 1.25
Torque Specification
4 ft-lbs (5 N·m)
Important Notes
Proper torque is essential to prevent damage to the terminals.
2

Fuel Injector Electrical Connector Bolt

M6 x 1.0
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Estimated value based on general industry standards.

Emissions Sensors

Torque specifications for Emissions_sensors

Emissions Sensors

1

EGR Valve Bolts

M10 x 1.5
Torque Specification
13 ft-lbs (18 N·m)
Important Notes
Torque value is within the recommended range of 11-15 ft-lbs (15-20 Nm).
2

Fuel Injector Bolts

M12 x 1.75
Torque Specification
12.5 ft-lbs (17 N·m)
Important Notes
Torque value is within the recommended range of 11-14 ft-lbs (15-19 Nm).
3

Oxygen Sensor Bolts

M18 x 1.5
Torque Specification
22.5 ft-lbs (30.5 N·m)
Important Notes
Estimated torque value based on industry standards for oxygen sensor bolts.

Engine Sensors

1

Mass Airflow Sensor (MAF) Bolts

M8 x 1.25
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Estimated torque value based on industry standards for MAF sensor bolts.
2

Crankshaft Position Sensor (CKP) Bolts

M10 x 1.5
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Estimated torque value based on industry standards for CKP sensor bolts.
3

Camshaft Position Sensor (CMP) Bolts

M10 x 1.5
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Estimated torque value based on industry standards for CMP sensor bolts.

Exhaust

Torque specifications for Exhaust

Exhaust Manifold Headers

1

Exhaust Manifold/Headers to Cylinder Head Bolts

M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Torque values are based on typical M10 bolt specifications. Ensure bolts are tightened in a crisscross pattern to evenly distribute pressure.

Exhaust Pipe Connections

1

Exhaust Pipe to Exhaust Manifold/Headers Bolts

M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Torque values are based on typical M10 bolt specifications. Ensure gaskets are properly seated before tightening.
2

Catalytic Converter to Exhaust Pipe Bolts

M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Torque values are based on typical M10 bolt specifications. Ensure gaskets are properly seated before tightening.
3

Muffler to Exhaust Pipe Bolts

M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Torque values are based on typical M10 bolt specifications. Ensure gaskets are properly seated before tightening.

Exhaust Support Components

1

Exhaust Hanger Bolts

M8 x 1.25
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Torque values are based on typical M8 bolt specifications. Ensure hangers are properly aligned before tightening.
2

Oxygen Sensor (O2 Sensor)

M18 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Torque values are based on typical M18 bolt specifications. Ensure the sensor is properly seated before tightening.
3

Exhaust Heat Shield Bolts

M6 x 1.0
Torque Specification
8.5 ft-lbs (11.5 N·m)
Important Notes
Torque values are based on typical M6 bolt specifications. Ensure heat shields are properly aligned before tightening.
4

Exhaust Flange Bolts

M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Torque values are based on typical M10 bolt specifications. Tighten bolts in a crisscross pattern to evenly distribute pressure.

Fuel

Torque specifications for Fuel

Intake Manifold

1

Throttle Body Bolts

M10 x 1.5
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Estimated torque value based on similar components.
2

Intake Manifold Bolts

M12 x 1.75
Torque Specification
14 ft-lbs (19 N·m)

Fuel Rail And Injectors

1

Fuel Rail Bolts

M10 x 1.5
Torque Specification
15 ft-lbs (20 N·m)
2

Fuel Injector Bolts

M8 x 1.25
Torque Specification
12 ft-lbs (16 N·m)
3

Fuel Injector O-Ring Bolts

M6 x 1.0
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Estimated torque value based on general industry standards.

Fuel Pump And Tank

1

Fuel Pump Mounting Bolts

M14 x 2.0
Torque Specification
29 ft-lbs (39 N·m)
2

Fuel Tank Strap Bolts

M12 x 1.75
Torque Specification
25 ft-lbs (34 N·m)

Fuel Filler Neck And Filter

1

Fuel Filler Neck Bolts

M10 x 1.5
Torque Specification
12 ft-lbs (16 N·m)
2

Fuel Filter Bolt/Nut

M12 x 1.75
Torque Specification
25 ft-lbs (34 N·m)

Fuel Pressure Regulator

1

Fuel Pressure Regulator Mounting Bolts

M10 x 1.5
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Estimated torque value based on general industry standards.

Hvac

Torque specifications for Hvac

Ac Compressor

1

A/C Compressor Mounting Bolts

M10 x 1.25
Torque Specification
32.5 ft-lbs (44 N-m)
Important Notes
Torque value is the midpoint of the provided range (29-36 ft-lbs). Ensure bolts are tightened in a crisscross pattern to avoid warping the compressor housing.
2

A/C Line Fittings

M12 x 1.5
Torque Specification
N/A
Important Notes
Hand-tighten only. Over-tightening can damage O-rings or fittings, leading to refrigerant leaks.

Evaporator Housing

1

Evaporator Housing Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N-m)
Important Notes
Torque value is the midpoint of the estimated range (7-9 ft-lbs). Ensure bolts are tightened evenly to prevent air leaks.

Blower Motor

1

Blower Motor Mounting Bolts

M5 x 0.8
Torque Specification
6 ft-lbs (8 N-m)
Important Notes
Torque value is the midpoint of the estimated range (5-7 ft-lbs). Avoid over-tightening to prevent damage to the motor casing.

Heater Core

1

Heater Core Inlet/Outlet Pipe Bolts

M8 x 1.25
Torque Specification
12.5 ft-lbs (17 N-m)
Important Notes
Torque value is the midpoint of the estimated range (11-14 ft-lbs). Ensure proper sealing to prevent coolant leaks.

Condenser

1

Condenser Mounting Bolts

M8 x 1.25
Torque Specification
15.5 ft-lbs (21 N-m)
Important Notes
Torque value is the midpoint of the estimated range (14-17 ft-lbs). Ensure proper alignment with the radiator.

Control Panel

1

HVAC Control Panel Mounting Screws

M4 x 0.7
Torque Specification
3 ft-lbs (4 N-m)
Important Notes
Torque value is the midpoint of the estimated range (2-4 ft-lbs). Avoid over-tightening to prevent damage to the plastic housing.

Suspension

Torque specifications for Suspension

Front Suspension

1

Strut/Shock Absorber Mounting Bolts

M14 x 1.5
Torque Specification
25.5 ft-lbs (34.5 N·m)
Important Notes
Estimated average value from specified range.
2

Control Arm Bolts

M16 x 1.5
Torque Specification
59.5 ft-lbs (80.5 N·m)
Important Notes
Estimated average value from specified range.
3

Ball Joint Nut

M18 x 1.5
Torque Specification
39.5 ft-lbs (53.5 N·m)
Important Notes
Estimated average value from specified range.
4

Tie Rod End Nut

M14 x 1.5
Torque Specification
25.5 ft-lbs (34.5 N·m)
Important Notes
Estimated average value from specified range.
5

Sway Bar Link Nut

M12 x 1.25
Torque Specification
32.5 ft-lbs (44 N·m)
Important Notes
Estimated average value from specified range.

Steering System

1

Steering Gear/Rack Bolts

M18 x 1.5
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Estimated average value from specified range.

Upper Control Arm Bushings

1

Upper Control Arm Bushing Bolts

M14 x 1.5
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Estimated value based on general industry standards.

Lower Control Arm Bushings

1

Lower Control Arm Bushing Bolts

M14 x 1.5
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Estimated value based on general industry standards.

Stabilizer Bar Mounting

1

Stabilizer Bar Mounting Bolts

M12 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Estimated value based on general industry standards.

Coil Spring Mounting

1

Coil Spring Mounting Bolts

M12 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Estimated value based on general industry standards.

Troubleshooting Guide

Common issues, diagnostic steps, and prevention guidelines

Common Issues

Bolt stretching, stripped threads, uneven torque patterns

Loose Components

Symptoms:
  • Rattling or vibration noises
  • Visible movement in components
  • Uneven panel gaps
Solutions:
  • Clean threads and mounting surfaces
  • Replace damaged fasteners
  • Apply proper torque in sequence
  • Use thread locker if specified

Stripped Fasteners

Symptoms:
  • Unable to achieve proper torque
  • Fastener spins freely
  • Visible thread damage
Solutions:
  • Use thread repair kit if appropriate
  • Install thread insert (HeliCoil)
  • Replace component if threaded hole is damaged
  • Upgrade to higher grade fastener if recommended

Overtightened Components

Symptoms:
  • Cracked or deformed parts
  • Broken fasteners
  • Compressed gaskets or seals
Solutions:
  • Replace damaged components
  • Use new fasteners
  • Follow proper torque sequence
  • Verify correct torque specifications

Diagnostic Steps

Visual inspection, torque verification, thread assessment

1

Visual Inspection

Inspect the affected area for any visible signs of damage or wear

  • Check for cracks or deformation
  • Look for signs of excessive wear
  • Verify proper fastener installation
2

Torque Verification

Verify the torque applied to the fasteners

  • Check the torque wrench calibration
  • Verify the torque specification
  • Compare the applied torque to the specification
3

Thread Assessment

Assess the condition of the threads

  • Check for signs of thread damage
  • Verify the thread type and size
  • Check for proper thread engagement

Prevention Guidelines

Best practices, maintenance tips, tool care

Best Practices

  • Always follow the recommended torque specification
  • Use the correct type and size of fasteners
  • Verify the torque wrench calibration regularly

Maintenance Tips

  • Regularly inspect the affected area for signs of wear or damage
  • Replace damaged or worn-out components promptly
  • Keep the work area clean and organized

Tool Care

  • Regularly clean and maintain the torque wrench
  • Store the torque wrench in a dry and secure location
  • Verify the torque wrench calibration before each use

Frequently Asked Questions

Find answers to common questions about torque specifications

Q1

What IS the torque specification for the lug nuts on a 1996-1999 Infiniti i30?

The torque specification for the lug nuts on a 1996-1999 Infiniti i30 IS 80 ft-lbs.

Q2

What IS the torque specification for the oil drain plug on a 1996-1999 Infiniti i30?

The torque specification for the oil drain plug on a 1996-1999 Infiniti i30 IS 25 ft-lbs.

Q3

What IS the torque specification for the spark plugs on a 1996-1999 Infiniti i30?

The torque specification for the spark plugs on a 1996-1999 Infiniti i30 IS 18 ft-lbs.

Q4

What type of torque wrench should I use to tighten the lug nuts on my 1996-1999 Infiniti i30?

You should use a torque wrench that IS calibrated to the correct torque specification for the lug nuts on your 1996-1999 Infiniti i30, which IS 80 ft-lbs.

Q5

What are some common mistakes people make when tightening bolts and nuts?

Some common mistakes people make when tightening bolts and nuts include over-tightening, under-tightening, using the wrong type of torque wrench, and not following the correct torque specifications.

Q6

What are the consequences of over-tightening or under-tightening bolts and nuts?

Over-tightening bolts and nuts can damage the threads, the bolt or nut, or the surrounding material. Under-tightening bolts and nuts can lead to loose parts, which can cause damage or failure.

Environmental Considerations

Temperature, humidity, and seasonal effects on torque specifications

Temperature Effects

Includes: High Heat, Cold Weather, Thermal Cycling

Temperature can significantly impact torque values and fastener behavior

Cold Weather

Effects:
  • Increased material brittleness
  • Higher torque required due to thread contraction
  • Reduced thread lubricant effectiveness
Recommendations:
  • Allow components to warm to room temperature when possible
  • Consider using winter-grade thread lubricants
  • Check torque values more frequently during winter months

Hot Weather

Effects:
  • Thermal expansion of components
  • Decreased friction in threads
  • Accelerated lubricant breakdown
Recommendations:
  • Check torque when components are at normal operating temperature
  • Use temperature-resistant thread lockers
  • Consider re-torquing after heat cycles

Humidity and Corrosion

Covers: Rust Prevention, Salt Exposure, Moisture Control

Moisture and corrosion can affect fastener integrity and torque values

High Humidity

Effects:
  • Accelerated corrosion formation
  • Reduced friction coefficient
  • Potential thread seizing
Prevention:
  • Use corrosion-resistant fasteners
  • Apply appropriate anti-seize compounds
  • Maintain proper protective coatings

Salt Exposure

Effects:
  • Rapid corrosion development
  • Thread damage
  • Seized fasteners
Prevention:
  • Regular underbody washing
  • Use of sacrificial anodes where appropriate
  • Application of protective coatings

Seasonal Maintenance

Spring, Summer, Fall, and Winter maintenance schedules

Spring

  • Inspect for winter damage
  • Clean and protect exposed fasteners
  • Check torque on critical components

Summer

  • Monitor heat-affected components
  • Check expansion-related loosening
  • Inspect cooling system mounts

Fall

  • Prepare for winter conditions
  • Apply corrosion protection
  • Verify all fasteners are properly torqued

Winter

  • More frequent inspection of critical fasteners
  • Check for salt damage
  • Monitor suspension component torque

Related Resources

Tools, service procedures, and technical bulletins

Recommended Tools

Digital Torque Wrench (10-100 Nm)

Essential for tightening fasteners to precise torque specifications, preventing damage and ensuring proper assembly. This range IS suitable for many applications on the I30.

  • Digital display for accurate readings
  • Audible alarm when target torque IS reached
  • Multiple units (Nm, ft-lb, in-lb)
  • Reversible ratcheting mechanism
Learn more
Service Procedures
Technical Service Bulletins

Legal Disclaimer

Important information about using this content

Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.

General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability

The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.

We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.

Technical Information
  • All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
  • Vehicle specifications and procedures may vary by model year, trim level, and region.
  • Always follow the manufacturer's recommended procedures and safety precautions.
  • Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
  • If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.

About the Author

Expert automotive knowledge and experience

Alan Montanye - Automotive Technical Specialist
ASE

Alan Montanye

Automotive Technical Specialist

ASE Master Certified Technician with over a decade of hands-on experience in automotive repair and diagnostics.

Facebook Contact
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions

Diagnostic

Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.

Repair

Expert in both traditional mechanical repairs and modern vehicle systems.

Additional Expertise

Documentation

Created over 500 detailed repair guides and technical documents.

Training

Conducted technical training sessions and contributed to repair databases.

Certifications & Research

Certifications

  • ASE Master Technician Certification
  • Advanced Diagnostic Specialist
  • Hybrid/Electric Vehicle Systems
  • Performance Tuning Expert

Research & Community

Actively researches emerging technologies and contributes to automotive forums.

© 2025 Infiniti Specs. All rights reserved.

Privacy Policy Terms of Service